-
Overview: HG Series Cylinder Scratch Board Dryer is a kind of rotating continuous drying equipment with internal heating conducting function. The material film will stick to the bottom of the rotating cylinder. The heat is transferred to the internal wall of the cylinder through piping system and it will be conducted to the external wall and material film. The moisture of the wet material film will be easily evaporated and the dried material will be scraped from the cylinder surface and transfer to the packing area by the screw conveyor.
-
Overview: The JG Series Airflow Dryer can rapidly remove moisture from the granules or powder that is easy to dehydrate (mainly water in surface). Because of the raw material stayed in the dryer only for a short time so the quality of finished products can be controlled to the best conditions. Our factory developed a reinforced device with stepless speed exchange based on basic dryer. When the wet raw material is fed through screw feeder, it will be fully mixed with hot airflow and the rotating knives will crush it into fine granule. The granule dries during the movement to the outlet and it finally enters the drying pipe under absorbing of air force. The humidity and heavy granule that is not absorbing of air force. At the place it is dried further. The humidity and heavy granule that is not absorbed by air will be continuously crushed and dried until it entering the drying pipe.
-
Overview: The drying process of FG Series Airflow Dryer is divided into two steps.First step: Utilize the tail air from second grade drying and mix with the supplemental hot air to process the first grade drying under positive pressure. The waste wet air will be exhaust out after reused. Second step: Use fresh air to process the second drying under negative pressure. The finished product will be measured and packaged.
The high temperature and low moisture tail air is used for the first grade drying which creates a complete circulation process. The supplementary hot air may be adjusted freely.
-
Overview: The drying oven is suitable for drying and dehydration of material and product for pharmaceutical, chemical, food, agricultural, aquatic, light industry, heavy industry; such as medicine raw material, medicine, Chinese herbal medicine, extractum, granules, powder, pill, packing bottle, pigment and dyes, dehydrated vegetables, dried fruit, sausages, plastic, resin, electric elements, varnish, and etc.
-
Overview: The damp raw material enters into helix bed from feeding inlet at the top and moves along with the helix bed under the action of excited force and gravity. The material is jumping up and down until it falls to the bottom layer. The clean hot air enters into it from the bottom of helix bed and carries out heat exchange with raw material and exhausted from the outlet at the top.
-
Overview: This machine is composed of transmission device, horizontal cylinder, coulter, and fly cutter. The raw material flows circumferentially along the cylinder and it will be tossed and sprinkled under action of the high speed rotating cutler. Therefore, the material can be evenly mixed in a shorter time.
All 57 , 49 - 54, Page 9/10
Overview: HG Series Cylinder Scratch Board Dryer is a kind of rotating continuous drying equipment with internal heating conducting function. The material film will stick to the bottom of the rotating cylinder. The heat is transferred to the internal wall of the cylinder through piping system and it will be conducted to the external wall and material film. The moisture of the wet material film will be easily evaporated and the dried material will be scraped from the cylinder surface and transfer to the packing area by the screw conveyor.
Overview: The JG Series Airflow Dryer can rapidly remove moisture from the granules or powder that is easy to dehydrate (mainly water in surface). Because of the raw material stayed in the dryer only for a short time so the quality of finished products can be controlled to the best conditions. Our factory developed a reinforced device with stepless speed exchange based on basic dryer. When the wet raw material is fed through screw feeder, it will be fully mixed with hot airflow and the rotating knives will crush it into fine granule. The granule dries during the movement to the outlet and it finally enters the drying pipe under absorbing of air force. The humidity and heavy granule that is not absorbing of air force. At the place it is dried further. The humidity and heavy granule that is not absorbed by air will be continuously crushed and dried until it entering the drying pipe.
Overview: The drying process of FG Series Airflow Dryer is divided into two steps.First step: Utilize the tail air from second grade drying and mix with the supplemental hot air to process the first grade drying under positive pressure. The waste wet air will be exhaust out after reused. Second step: Use fresh air to process the second drying under negative pressure. The finished product will be measured and packaged. The high temperature and low moisture tail air is used for the first grade drying which creates a complete circulation process. The supplementary hot air may be adjusted freely.
Overview: The drying oven is suitable for drying and dehydration of material and product for pharmaceutical, chemical, food, agricultural, aquatic, light industry, heavy industry; such as medicine raw material, medicine, Chinese herbal medicine, extractum, granules, powder, pill, packing bottle, pigment and dyes, dehydrated vegetables, dried fruit, sausages, plastic, resin, electric elements, varnish, and etc.
Overview: The damp raw material enters into helix bed from feeding inlet at the top and moves along with the helix bed under the action of excited force and gravity. The material is jumping up and down until it falls to the bottom layer. The clean hot air enters into it from the bottom of helix bed and carries out heat exchange with raw material and exhausted from the outlet at the top.
Overview: This machine is composed of transmission device, horizontal cylinder, coulter, and fly cutter. The raw material flows circumferentially along the cylinder and it will be tossed and sprinkled under action of the high speed rotating cutler. Therefore, the material can be evenly mixed in a shorter time.
